Convert Watt per Square millimeter-Steradian to Milliwatt per Square meter-Steradian (W/(mm²·sr) to mW/(m²·sr))

To achieve the desired result as quickly as possible, it is best to enter the value to be converted as text, for example '885 W/mm2sr to mW/m2sr' or '885 W/mm2sr into mW/m2sr' or simply '885 W/mm2sr':

In most cases, the word 'to' (or '=' / '->') can be omitted between the names of the two units, for example '885 W/mm2sr mW/m2sr' instead of '885 W/mm2sr to mW/m2sr'.
The basic operations of arithmetic: exponent (^), square root (√), multiplication (*, x), brackets, pi (π), subtraction (-), division (/, :, ÷) and addition (+) are all permitted at this point
Instead of 1.92 x 10^5, 1.92e5 can be written. The 'e' stands for 'exponent'.
Instead of the Greek letter 'µ' (= micro), a simple 'u' can be used, for example uPa instead of µPa.
In the abbreviations for 'square' and 'cubic', the '^' character can be omitted from '^2' and '^3'. Square centimetres can therefore be written cm2 instead of cm^2.

or: Using the calculator with the selection lists

Choose the right category from the selection list, in this case 'Radiance'.
Next enter the value you want to convert.
From the selection list, choose the unit that corresponds to the value you want to convert, in this case 'Watt per Square millimeter-Steradian [W/(mm²·sr)]'.
Finally choose the unit you want the value to be converted to, in this case 'Milliwatt per Square meter-Steradian [mW/(m²·sr)]'.

Use the full power of this unit converter to convert W/mm2sr to mW/m2sr

With this calculator, it is possible to enter the value to be converted together with the original measurement unit; for example, '873 Watt per Square millimeter-Steradian'. In so doing, either the full name of the unit or its abbreviation can be usedas an example, either 'Watt per Square millimeter-Steradian' or 'W/mm2sr'. Then, the calculator determines the category of the measurement unit of measure that is to be converted, in this case 'Radiance'. After that, it converts the entered value into all of the appropriate units known to it. In the resulting list, you will be sure also to find the conversion you originally sought. Alternatively, the value to be converted can be entered as follows: '90 W/mm2sr to mW/m2sr' or '65 W/mm2sr into mW/m2sr' or '85 Watt per Square millimeter-Steradian -> Milliwatt per Square meter-Steradian' or '80 W/mm2sr = mW/m2sr' or '75 Watt per Square millimeter-Steradian to mW/m2sr' or '70 W/mm2sr to Milliwatt per Square meter-Steradian' or '60 Watt per Square millimeter-Steradian into Milliwatt per Square meter-Steradian'. For this alternative, the calculator also figures out immediately into which unit the original value is specifically to be converted. Regardless which of these possibilities one uses, it saves one the cumbersome search for the appropriate listing in long selection lists with myriad categories and countless supported units. All of that is taken over for us by the calculator and it gets the job done in a fraction of a second.

If a check mark has been placed next to 'Numbers in scientific notation', the answer will appear as an exponential. For example, 4.412 222 182 071 ×1021. For this form of presentation, the number will be segmented into an exponent, here 21, and the actual number, here 4.412 222 182 071. For devices on which the possibilities for displaying numbers are limited, such as for example, pocket calculators, one also finds the way of writing numbers as 4.412 222 182 071 E+21. In particular, this makes very large and very small numbers easier to read. If a check mark has not been placed at this spot, then the result is given in the customary way of writing numbers. For the above example, it would then look like this: 4 412 222 182 071 000 000 000. Independent of the presentation of the results, the maximum precision of this calculator is 14 places. That should be precise enough for most applications.
Instead of '4^3' you can also write '4 exp 3' or '4 pow 3'.
Instead of '√16' you can also write 'sqrt 16'.
The mathematical functions acos, pow, sqrt, sin, atan, exp, cos, tan and asin can also be used. Example: sin(90), tan(90°), atan(1/4), acos(1), cos(pi/2), 3 pow 2, sin(π/2), asin(1/2), sqrt(4) or 2 exp 3
If required, the result can be rounded to a certain number of decimal places wherever it makes sense.
Furthermore, the calculator makes it possible to use mathematical expressions. As a result, not only can numbers be reckoned with one another, such as, for example, '35 * 30 W/mm2sr'. But different units of measurement can also be coupled with one another directly in the conversion. That could, for example, look like this: '45 Watt per Square millimeter-Steradian + 40 Milliwatt per Square meter-Steradian' or '25mm x 20cm x 15dm = ? cm^3'. The units of measure combined in this way naturally have to fit together and make sense in the combination in question.