Slug per second into Ton (short/US) per second
Direct link to this calculator:
How many Ton (short/US) per second make 1 Slug per second?
Convert Slug per second to Ton (short/US) per second (slug/s to tn/s):
- Choose the right category from the selection list, in this case 'Mass flow rate'.
- Next enter the value you want to convert. The basic operations of arithmetic: addition (+), subtraction (-), multiplication (*, x), division (/, :, ÷), exponent (^), square root (√), brackets and π (pi) are all permitted at this point.
- From the selection list, choose the unit that corresponds to the value you want to convert, in this case 'Slug per second [slug/s]'.
- Finally choose the unit you want the value to be converted to, in this case 'Ton (short/US) per second [tn/s]'.
- Then, when the result appears, there is still the possibility of rounding it to a specific number of decimal places, whenever it makes sense to do so.
With this calculator, it is possible to enter the value to be converted together with the original measurement unit; for example, '134 Slug per second'. In so doing, either the full name of the unit or its abbreviation can be usedas an example, either 'Slug per second' or 'slug/s'. Then, the calculator determines the category of the measurement unit of measure that is to be converted, in this case 'Mass flow rate'. After that, it converts the entered value into all of the appropriate units known to it. In the resulting list, you will be sure also to find the conversion you originally sought. Alternatively, the value to be converted can be entered as follows: '30 slug/s to tn/s' or '24 slug/s into tn/s' or '4 Slug per second -> Ton (short/US) per second' or '84 slug/s = tn/s' or '77 Slug per second to tn/s' or '76 slug/s to Ton (short/US) per second' or '33 Slug per second into Ton (short/US) per second'. For this alternative, the calculator also figures out immediately into which unit the original value is specifically to be converted. Regardless which of these possibilities one uses, it saves one the cumbersome search for the appropriate listing in long selection lists with myriad categories and countless supported units. All of that is taken over for us by the calculator and it gets the job done in a fraction of a second.
Furthermore, the calculator makes it possible to use mathematical expressions. As a result, not only can numbers be reckoned with one another, such as, for example, '(70 * 63) slug/s'. But different units of measurement can also be coupled with one another directly in the conversion. That could, for example, look like this: '134 Slug per second + 402 Ton (short/US) per second' or '68mm x 65cm x 17dm = ? cm^3'. The units of measure combined in this way naturally have to fit together and make sense in the combination in question.
The mathematical functions sin, cos, tan and sqrt can also be used. Example: sin(π/2), cos(pi/2), tan(90°), sin(90) or sqrt(4).
If a check mark has been placed next to 'Numbers in scientific notation', the answer will appear as an exponential. For example, 1.048 575 990 458 ×1027. For this form of presentation, the number will be segmented into an exponent, here 27, and the actual number, here 1.048 575 990 458. For devices on which the possibilities for displaying numbers are limited, such as for example, pocket calculators, one also finds the way of writing numbers as 1.048 575 990 458 E+27. In particular, this makes very large and very small numbers easier to read. If a check mark has not been placed at this spot, then the result is given in the customary way of writing numbers. For the above example, it would then look like this: 1 048 575 990 458 000 000 000 000 000. Independent of the presentation of the results, the maximum precision of this calculator is 14 places. That should be precise enough for most applications.